 |
|
|
|
 |
 |
 |
ACTUATECH PNEUMATIC ACTUATOR PERFORMANCES
- Special scotch yoke design that gives an increased torque and the seat break out point.
- The use of steel parts instead of aluminium parts, ensures high wear resistance to the internal mechanism and
consequent longer working life.
- Compact design with reduced overall dimension allows an easy handling & minimal air (energy) consumption.
- Special compound seals and guide on the sliding pistons, ensures self lubrication for life.
- Internal bores are fine lapped and have anodized surface treatment for lower friction and perfect piston sealing.
- Maintenance free for the full actuator working life.
- Standard stainless steel drive shaft protects against the environmental corrosion.
- Standard stroke adjustment.
- Atex 94/9/CE for suitability of the equipment intended for the use in Potentially Explosive Atmosphere.
Actuator Nominal Torque: from 8 Nm to 1920 Nm.
Mounting flange according with DIN/ISO 5211, DIN 3337: F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16.
NAMUR standard pressure connection.
Rotation angle: 92° (-1°+91°).
Stroke Adjustment : 10°
Nominal pressure: 5,6 bar; maximum operating pressure 8,4 bar.
The torque is directly proportional to the operating pressure.
For the simple acting (spring return) actuators the reverse torque is performed only by the spring action, and is
independent from the operating pressure.
Temperature: from 0°C to 80°C; using dry air from -20°C to +80°C.
(Special version HT -20°C to +150°C or LT -50°C to +60°C).
Operating media: compress filtered air not necessary lubricated.
In case of lubricated air use non-detergent oil compatible with NBR rubber.
All the models are available in double acting "GD" and simple acting "GS" version. |
 |
 |
 |
- Special scotch yoke design that gives an increased torque and the seat break out point.
- The use of steel parts instead of aluminium parts, ensures high wear resistance to the internal mechanism and
consequent longer working life.
- Compact design with reduced overall dimension allows an easy handling & minimal air (energy) consumption.
- Special compound seals and guide on the sliding pistons, ensures self lubrication for life.
- Internal bores are fine lapped and have anodized surface treatment for lower friction and perfect piston sealing.
- Maintenance free for the full actuator working life.
- Standard stainless steel drive shaft protects against the environmental corrosion.
- Standard stroke adjustment ( patented see. fig A )
- Atex 94/9/CE for suitability of the equipment intended for the use in Potentially Explosive Atmosphere.
Actuators Nominal Torque: from 1440 Nm to 8000 Nm.
Mounting flange according with DIN/ISO 5211, DIN 3337: F16 - F25.
NAMUR standard pressure connection.
Rotation angle: 100° (-5°+95°).
Stroke Adjustment: 10°
Nominal pressure: 5,6 bar; maximum operating pressure 8,4 bar. (GD8000 pmax 7 bar )
The torque is directly proportional to the operating pressure.
For the simple acting ( spring return ) actuators the reverse torque is performed only by the spring action, and is
independent from the operating pressure.
Temperature: from 0°C to 80°C; using dry air from -20°C to +80°C.
(Special version LT -50°C to +60°C).
Operating media: compress filtered air not necessary lubricated.
In case of lubricated air use non-detergent oil compatible with NBR rubber.
All the models are available in double acting "GD" and simple acting "GS" version. |
|
|
Actuatech will be free to change all specifications
and data at any time REV. 02/2008 |
|
|
|
| via
F.lli Capponi, 126/128 - 25068 Sarezzo (BS) Italy - tel +390308908142
- fax +390308908143 - actuatech@actuatech.com
|
 |
|
|
